Android BMW Z4 E89 Navigation GPS Head unit Installation manual

Android BMW Z4 Navigation GPS Installation manual

When order the aftermarket Android BMW Z4 Navigation Screen for BMW Z4 E89(2006-2012), you should pay attention to serveral points as below:

1. If your BMW Z4(E89) has a factory screen,or with a storage box,
you can order our model [B224]

2, If your car without storage box (nor factory screen), there is no way to install our model,don't order it.

3, When your BMW Z4 with factory screen (CIC), the factory iDrive knob can work in original CIC system and also can work in new Android screen.

4. If there is storage box on the dashboard of your BMW Z4(E89), then your car does not equip with the factory iDrive knobs either. You can only operate it via touchscreen,but you can order an iDrive knob from us.

5. The screen is fixed, it does not like the factory BMW Z4(E89) screen which can flip down.

6. To install this Android BMW Z4 Navigation, your Z4(E89) must equip with AUX IN port to get sound. If there is no AUX IN port on your car, please DO NOT buy this model.


Installation steps:

1: Before installation(right hand drive same as left hand drive)    2, Pull up the cover around the gear (don't remove it from the gear)

 bmw z4 original dashboard and first pull up the cover around the gear

3: Remove the cover in central console (so that to install the idrive and arrange the AUX cable under this cover)   4: Remove the frame around the factory Radio panel

 remove the cover in the central console and take off the frame around the BMW Z4 factory radio

5: The cover was removed   6: Remove 4 screws and take out the factory radio head unit, and remove all the harness on the back of head unit

 Remove the screws and take out the factory BMW Z4 Radio head unit ,remove all harness on the back

7: Remove the 2 optical fiber cables from the factory harness and insert it to our power cable (female connector)   8: Remove the plastic cover ( there is 5 screws to fix this cover, please notice there is 1 screw on the side of the cover)

 move the optical fiber to our power cable, take off the plastic frame in the front of dashboard

9, After take off the screws, the cover can be removed   10, There are 3 connectors on the back , remove all of them

 take off the front cover and remove 3 connectors on the back

11,After take off 2 screws, the AC Vents can be removed. 12, Remove the cover on top (be carefull, there is a speaker and a sensor under this cover)

 remove the AC Vents and then remove the cover on the top

13, Remove the 4 screws showed as below photo,so that to remove the cover of factory monitor   14, The cover for factory monitor can be remove: just slide forward then will be ok.

 take off the screws and remove the cover on the top of factory BMW Z4 monitor

15, Remove the cover showed as below  16, Now the factory monitor can be removed

 remove the cover and then take out the bmw z4 monitor

 

17,Remove all the connections on the back of factory monitor  18, Arrange the power cable/USB/GPS antenna to the back of our android screen, then insert all harness to the android screen

 first remove all harness on the back of factory screen then insert all cables to our monitor

19, Install the android screen  20, If you order the models with iDrive, don't forget to connect the idrive connector.

 install our android screen to bmw z4 , and if the car with idrive, you need to connect the idrive control cable

21, You also notice to connect the AUX cable,otherwise, it will no sound output  22, Connect all harness to the back of factory radio head unit

 connect the AUX cable and insert the power cable and other factory harness to factory radio head unit

23, Install the idrive knob in the central console   24, Recover the car dashboard

 install the idrive knob to central console and recover the factory bmw z4 dashboard, the installation is done

 

 

Comments

0 comments

Write a comment

Comments are moderated